Tag Archives: compilers

Low power firmware – timers, compilers and structures

 

The last two posts were about general concepts around low power firmware design. This week I’ll start getting into details including some code examples.

Timers

  • Use the largest clock pre-scaler that provides the resolution your firmware needs. The pre-scaler is typically a 4 to 8 bit counter while the counter/timer may be 8, 16 or 32 bits. Letting the pre-scaler run faster so the timer runs slower can reduce power considerably, particularly for free-running timers.
  • Software based timers running on a tick interrupt are easy to implement and may be necessary if your application requires more than a few timers to be running simultaneously.  Dedicated timers will be more power efficient IF the time-out period can be achieved with a single terminal count interrupt from the timer.
  • When using a periodic tick interrupt for software timers, use the longest tick interval your code can tolerate. If sections of your code require tight timing it will usually be more efficient to use one timer with a longer tick interval for general use and another timer for with a short tick interval for the tight timing.
  • For a timeout protection timer that doesn’t have tight timing requirements, consider using an RTC alarm interrupt for a 1 second (or longer) timeout. The RTC running at 32Khz should be much lower power than an 8 or 16 bit timer using a clock divided down from the micro’s much faster clock. This also provides a means for long timeout periods without taking periodic tick interrupts. On most modern micros, the RTC is functional even without a battery voltage present but may still require a dedicated crystal so be sure to check the datasheet if you aren’t using the RTC for its intended purpose.
  • Turn off timers when they aren’t being used. If software based timers are appropriate for your application, turn off the free-running timer when it is not being used. This sounds like a no-brainer but it’s common to leave the free-running timer running all the time. For dedicated timers, this is usually just a matter of selecting the right mode for the timer so it stops automatically when it reaches the terminal count.
  • For ultra-low power, when possible use a timer that counts down to 0 or counts up to all ones and generates an interrupt. Using a counter and match register containing the terminal count value requires more circuitry to be active and will consume more power.

Compilers

If you are writing firmware in any high level language you need to become intimately familiar with the compiler and learn what it does well and what it doesn’t it. The only way to do that is to write some code and then examine the assembly code it generates.

  • Efficiency – Every instruction your micro executes that isn’t required is wasted power. Compiler efficiency is usually a case of you get what you pay for. Free and low-cost compilers based on the GNU compiler typically produce code 2X to 5X larger, slower and less power efficient than a compiler written for a specific architecture.
  • In-line assembly code – If you decide to use assembly language for time critical sections of code or for other reasons, you need to research how your compiler handles in-line assembly instructions. In some compilers, the registers you think you are using are actually memory based variables. If your assembly code uses many variables or contains a loop that is executed more than a few times, you are generally better off calling a function written in actual assembly code since the function calling overhead uses less power than the pseudo assembly code. If you do use in-line assembly language, review the compiler generate assembly language before and after your assembly language code to see how much overhead the compiler imposes for saving/restoring the micro state information.
  • Compiler options – Compilers usually have many options, some of which can greatly increase or decrease the power efficiency of your code. A few things to look for:
    • Position independent code – Disable this option unless you absolutely need it. The relative addressing required for position independent code will use more power than fixed location code on every jump/call instruction executed.
    • Optimization options – Compilers typically provide options to optimize the generated code for speed or for size. The optimizations made for speed should also improve power efficiency since fewer clocks uses less power but will result in larger programs. If you are tight on code space, check to see if your compiler supports optimization on a per file basis so you can optimize the most frequently executed sections of code.

Structures

Structures are great for organizing variables but you need to consider whether this convenience is worth the cost in power compared to individual variables. A few things to consider:

  • Every time a structure element is used the micro has to add the element offset to the structure base address. On most 32-bit micros this is USUALLY achieved with an indexed addressing mode so no additional clock cycles are required (but check the assembly code to make sure). On a low-end 8-bit micro this requires code to calculate the address, taking 8 to 10 instructions or more.
  • Arrays of structures further complicate the math involved in calculating addresses. To calculate the offset into the array, the array index must be multiplied by the structure size and that is done in software on most micros used in embedded applications. If the array only contains a few instances of the structure it can be considerably more power efficient to have individual structures with another variable containing a pointer to the structure to use. Another technique for use with larger arrays will be discussed in the “Arrays and structures” section.
  • Don’t assume your compiler is smart enough to calculate the base address for a particular structure in an array once and use it for several consecutive lines of C code that access that structure. There is a good chance it will calculate that base address for each line of C code. To use less power, use a pointer to the structure in this situation, the compiler should only calculate the address based on the offset for structure members.

code_struct_ptr

 

  • One place where structures may work to save power is in parameter passing. Particularly with low-end 8 bit micros, passing multiple parameters can be considerably more expensive in terms of power and time than passing a pointer to a structure containing those parameters. The example below illustrates this, even using the structure for the return value.

code_struct_param_pass

Next week I’ll continue on low power firmware design with switch statements and arrays/structures.